Archive for July, 2015

Barracuda Phone System Default Admin Credentials

July 22, 2015

The Barracuda Phone System is a telphony solution that comes with default credentials. The “Getting Started” guide shows the console uses defaults:

At the Administrative Console prompt login, enter the credentials: admin/admin

The next step of the guide shows they are used for the web interface too:

In a web browser, enter the Barracuda Phone System IP address, for example, type
Log in to the web interface by entering the credentials admin/admin.


Canon ImageFORMULA DR Series WU10 WI-FI Enabled Document Scanner Multiple Default Passwords

July 18, 2015

The Canon ImageFORMULA DR Series WU10 is a Wi-Fi enabled high-speed document scanner. According to the manual it comes with two defaults:

Default wireless password / security key:

Web Interface (over wireless) default admin credentials:


Motorola VT2542 Voice Gateway Web Interface Default Admin Credentials

July 17, 2015

The Motorola VT2542 Voice Gateway router uses a web interface for device management. According to the manual it comes with default admin credentials:


ALCATEL ONETOUCH MiFi Y580 Wireless Hotspot Router Default Admin Password

July 16, 2015

The ALCATEL ONETOUCH MiFi Y580 Wireless Hotspot Router uses a web interface for device management. According to the manual it has a default admin password:

2.1 login the configuration page
Open the browser, and then input the address The page displayed
as bellow:
The default login password is admin.

Panasonic Network Cameras Default Admin Credentials

July 15, 2015

Panasonic Network Cameras (Models WV-SW598, WV-SW397A, WV-SW397, WV-SC588 and WV-SC387) allow for network access to control and monitor them. According to the manual they come with default admin credentials:

• It is possible to enhance the network security by encrypting the access to cameras using the HTTPS function.
Refer to the Operating instructions on the provided CD-ROM for how to configure the HTTPS settings
• Click the [Setup] button on the “Live” page, the user authentication window will be displayed. Enter the default
user name and password as follows, and log in.
User name: admin
Password: 12345

Barracuda CudaSign Web Interface Default Admin Credentials

July 14, 2015

Barracuda CudaSign “is a secure eSignature solution allowing organizations to obtain legally binding signatures from customers, partners, and employees in seconds, reducing document turnaround up to 90%.” According to the install documentation the setup process uses default admin credentials:

The Barracuda CudaSign Server initially displays the Boot Menu. Once fully booted, the Administrative Console login prompt displays. Log in using the admin login credentials admin/admin.

Once installed the documentation also shows the web interface has default credentials:

From a web browser, enter the Barracuda CudaSign Server IP address, followed by the default Web Interface HTTP Port (:8000).
Log in to the administration interface using admin for both the username and password


HP 3PAR Secure Service Policy Manager Default Admin Credentials

July 13, 2015

HP 3PAR Secure Service Policy Manager “is server-based software application that enables customers to control and monitor communications between the 3PAR Secure Service Custodian (Custodian) and the 3PAR Secure Service Collector Server (Collector Server).” It also installs with Tomcat 5.x for access to the web interface for management (http://system:8080/admin). According to the manual it installs with default admin credentials:

The Apache Tomcat5 Web server is configured with one default 3PAR Policy Manager user and
password as follows:
■ User name = admin
■ Password = admin
Use this login information to access the Policy Manager user interface.

Siemens SC 7000 / SC 9000XL Patient Monitors Default Admin Passcode

July 12, 2015

The Siemens SC 7000 and SC 9000XL Patient Monitors come with a default passcode that requires physical access but gives complete control over the device. According to the manual:

The Service Menu is accessed via the Monitor Options selection under the Monitor Setup function on the Main Menu. To access the Service menu and related functions, do the following:
1) Select Monitor Setup on Level 1, then select Biomed on Level 2, and then select Service on Level 3.
2) Input the service password (4712).
Note: In general, the Service Menu provides access to the following (may vary with software version):
• Language selection
• Regulation
• Alarm Sounds
Network control
Network Configuration (requires installed SW version ≥VC2)
• Transport Brightness
• Line frequency setting
Restore factory defaults
• Copy setups to card
• Copy setups to monitor
Install Software
Locked Options
• Waveform Simulator

GE Healthcare FASTlab Synthesizer Default Credentials

July 12, 2015

The GE Healthcare FASTlab Synthesizer runs on Windows 7. According to the manual it tells the admin to install it with specific credentials. The manual doesn’t say if things won’t work if you choose different credentials. Affects versions: 1.1.68, 2.0.39, 2.0.40

Enter the user Name AdminFASTlab and the computer name, then click “Next”
Enter “Healthcare” as the password and “Default from Documentation” as the password hint and click “Next”:

Once installed there are default credentials to access the device physically:

The login window appears. You now need to enter your user name and password and then click on the “Login” button. The default credentials are Login Name “Admin” and Password “admin“. It his highly recommended to change the credentials after installation.

BK Medical Aps Ultrasound Systems Default Credentials

July 12, 2015

BK Medical Aps bk3000 Ultrasound Systemallows you to routinely see anatomy and micro-vascularization not seen with conventional ultrasound.According to the manual it has default administrator credentials. You can attach a network drive or connect to a network printer but it doesnt look like you can login to the device remotely.

Password Setup
If your system is set up to be password-protected, use the Password Setup window to change your password. If you are a superuser with administrative privileges, you can add or remove users, reset their passwords, and enable or disable password protection.
NOTE: Usernames and passwords must each be no longer than 16 characters. The username is not case-sensitive, but the password is case-sensitive. (Case-sensitive means that B is not the same as b.)
The default superuser name and password are:
• Name: administrator
• Password: superuser

This also affects the Pro Focus 2202 Ultrasound System and the Flex Focus 1202 Ultrasound System.